SpitFireIII Hardware & Software
Installation Quick-Start Guide

Be sure and Bookmark this page for future reference.

The first thing to do is to make sure that you have all the components that are required for this installation. Please check the minimum requirements listed below before you process.

REQUIREMENTS:

• The computer that you are installing the board and software into needs to have the following minimum requirements.
• Pentium 3 computer with 600MHz processor or higher
• 2GB of available hard drive space
• Available PCI or ISA slot depending on the board that is to be installed
• Windows 2000 Pro (not an upgrade)
• VGA monitor capable of displaying 800x 600 minimum
• Sound blaster or compatible sound card
• Microphone and speakers
• 56K modem
• pcAnywhere (required for support)

DIALOGIC INSTALLATION PROCEDURE:

The boards listed below need to have the jumpers set prior to installation:

• Dialog/4
• Proline/2V
• Dialog/4D

The above boards are all ISA type boards and require the jumpers to be set in place before putting the card in the computer. Important if these jumpers are not set the board will not start when installed.

The recommended setting is IRQ7. If this is the only dialogic board in the system JP7 must have a jumper installed. All boards that are installed need to have the same IRQ.

The boards listed below do not need to have the jumpers set prior to installation:

• Dialogic D/4 PCI
• Dialogic D/41ESC
• Dialogic HD PCI

All PCI and ESC boards do not have jumpers that need to be set for the specific IRQ ports, these can be set from the Dialogic DCM software. It is important to note that on all ESC cards if you are using more than one, an SC bus cable is required to connect the boards together. ESC boards also need to have a different board ID# set.

Once the jumpers have been configured and the board(s) installed in the computer, you are ready to proceed with the installation.

The next step is to load the CD with the installation software into your CD Rom.

Put your mouse on the MyComputer icon and right-click with your mouse.

This will open up an "Option" tab as shown above.

This will open up a window that will show the contents of your computer. Take your mouse and put the arrow on the (D:) drive or the drive letter of your CD-Rom.

This will display the contents of the CD that contains the software for installation.

The first program to be installed is the Dialogic software. Take your mouse and select the "Dialogic 5.01" folder and left-double-click to open this folder.

The next step is to select the "setup.exe" file. Put your mouse on it and left-double-click to start the installation of the software.

The above screen is the first screen you will see, and the next screenshots will take you thru the installation windows of the Dialogic software (follow the example as shown).

Insert your Name and Company in the above windows.

Select the "Typical" option above. You will see the following screens as shown

Next, de-select the check marks in the above boxes.

Setup is now complete. Once you click on the OK button you will be prompted to reboot the computer. Do so.

When the computer has rebooted, select the "Start" tab as shown above on your computers desktop.

Select the "Dialogic System Software" option from the menu as shown above.

Select the "Dialogic Configuration Manager-DCM" as shown above.

This will open up the box that you see above (the detection process may take several minutes). If this is an ESC card or PCI, the system will detect the boards automatically. If these are ISA, non-ESC cards, they will need to be added manually.

The example shown above is a non-ESC card, therefore we need to add the board manually.

The next step is to add the device. Select "Add Device" from the "Action" tab as shown above.

This will open up the window shown above. Select "D/x1D" as shown on the left, and than select the particular model that you have installed in the computer as shown in the screen above.

In the above example the board that is installed is the "Dialog/4".

The next screen will ask you for a name of the card. Choose any name you wish, as long as it is different for each board that is installed.

Select the "Next" tab at the bottom of the screen.

If this is a non-ESC board, set the IRQ value that was set on the board. Check the manual that comes with the Dialogic card for this information. Leave the memory address at d0000.

Select "D41Dinterupt" under "Paramater".

Change the value by clicking on the arrow as shown in the picture above. If IRQ 7 is not shown in the drop down window, just add it manually.

Then click on the "Apply" button to save the settings, and then the "OK" button.

The screen above is the view that will be displayed next.

The next step is to start the board(s) by selecting the green circle with your mouse and left-double-clicking.

If everything is set correctly the bottom of the Dialogic screen will display the words running. This means that you have completed the installation of your Dialogic board(s).

The last step for installation of the Dialogic card(s) is to set the boards to start-up automatically every time you restart the computer. This is done by clicking on the "Service" tab as shown in the above screen.

Put your mouse over "Startup Mode" and "Automatic / Manual" options will pop up.

Select the "Automatic" option by clicking on it with your mouse.

The next step is to exit out of the Dialogic Configuration Manager by clicking on the "X" in the upper far right corner.

The next step is to install the CoolEdit" software for the .wav files. Select the "c96setup.exe" file and left-double-click to begin the installation.

Select the "OK" button with your mouse to begin.

Stay with the default setting and click "OK", then continue with the installation as shown in these images.

When CoolEdit has been installed, the screen above will display. Select "OK" with your mouse and it will pull up a sample .wav file.

Click on the "Play" button and you should hear the file. Make sure that you have the speakers attached to the sound card of your computer.

The final installation is the SpitfireIII software. Left double click on the "SpitFireIII.EXE" option as shown above and just use all the default settings. Please note that during the installation, if your computer does not have MDAC loaded, the system will prompt you to reboot after it has installed this in your computer, and then will continue with the installation.

Follow the next set of screens as shown until the installation is completed.

The software has now been installed successfully and the computer needs to be rebooted. Click "OK" and reboot.

Congratulations! Your installation is complete!

Please refer to the Training CD and manual for using the software.

To return to the OPC Marketing website click here